Home  >  Chemical Process Machinery  >  Chemical Machinery & Equipment  >  Drying Equipments  >  Dry Cabinet

slag aac brick making machine, 1.Extreme lightweight50%, 2.High fire resistance:4hours, 3.density:500kg/m3, 600kg/m3, 700kg/m - details see: https://www.machineto.com/slag-aac-brick-making-machine-10288294

slag AAC brick making machine

Introduction of slag AAC brick making machine

1.Autoclave Aerated Concrete Block (AAC Block) is the light and porous building material.

2.features of aac block:It has the advantages of Light Weight, Keeping Temperature, Heat Resistant, Fireproof, High Intensity, Good Sound Insulation and Machinability, Conveniently Mechanized Construction, etc.

3.size of AAC block:AAC Block can be made into many different size of blocks (for example: 600× 200× 100, 600× 200× 125, 80× 80× 180, 240× 115× 53, etc), widely used for industry building and common house building. They are becoming more and more popular in the world, in the near future, they will completely replace the Clay Bricks and Normal Concrete Blocks in building construction.

Conception conception of slag AAC brick making machine :

1.the density of aac bricks:The density of common concrete block is around 1600-2400kg/m3, but Aerated Concrete Block is 500kg/m3, 600kg/m3, 700kg/m3.

2.raw material of aac bricks: It has not the big grain, mainly made from silicon material, for example: Fly ash, sand, cement, quick lime, gypsum and so on.

3.process of aac brick making:In brief, there are 5 steps to make AAC Block, first, preparing raw material; Second, mixing the measured raw material to make slurry and pouring; Third, pre-ageing and cutting the green block body; Fourth, grouping the cut block and autoclaving; Fifth, packing the autoclaved block and transporting out of plant.

Production Engineering:

1. First, dose and match measured raw materials

2. After distributing, feed raw material into pouring mixer to make slurry

3. Through thoroughly mixing, the slurry is poured to mould

4. After pre-curing with a certain temperature & time, the block would reach certain hardness prepare for cutting

5. Tilting hoister would turn over 90 degree of mould

6. Then open the mould & separate it from block, take the block with side plate with cutting cart

7. The block then be cut through the cutter firstly of two vertical sides of block

8. Secondly the horizontal cutting

9. Finally the vertical cutting

10. After cutting, the block is hanged to trolley with side plate by semi-finished product hoister

11. Organizing the cut blocks and put them into autoclave

12. Hardening the blocks under certain temperature and pressure

13. Take finished products out of autoclave

14. The finished product hoister takes the finished product to stock shield

15. Packed for loading

16. The side plate return back by side plate roller

17. Side plate would be organized with open mould

18. Clean the mould and preparing for next pouring

19. Steel bars processing line for slab production

slag AAC brick making machine Advantage

1.Large variety of sizes:AAC can be produced in a large variety of sizes, from standard blocks to large reinforced panels;

2.Excellent thermal insulation:AAC has a very low thermal conductivity and therefore a very high thermal energy efficiency is achieved. This results in savings on heating and cooling costs;

3.Extreme lightweight:AAC weighs approximately 50% less than other comparable building products;

4.High compressive strength:AAC is a solid product, therefre making it highly load bearing. The entire surface area is used in structural calculations;

5.High dimensional accuracy:As a result of its dimensional accuracy, AAC is extremely easy to install, as no thick set mortar is required;

6.Great acoustic insulation:The porous structure of AAC provides a high acoustic insulation;

7.High fire resistance:AAC has an extremely high fire rating of at least 4 hours and more;

8.Termite resistance:AAC can not be damaged by termites or insects;

9.High workability:As a result of the excellent size/weight ratio, constructing with AAC is very rapid. Even

Though AAC is a solid building material, it can be cut, sawn, drilled, nailed and milled like wood, making it an extremely workable product.