Home  >  Chemical Process Machinery  >  Reactors

1)High oil yield, 2)100% Pollution-free, 3)Energy conservation, 4)Automatic welding, 5)Safety - details see: https://www.machineto.com/pyrolysis-reactor-10301829

pyrolysis reactor

Model	Feeding time	Processing time	Cooling time	Discharge slag	totally
2200*6000	2hours	7-8hours	2hours	2hours	14hours
2200*6600	2hours	8hours	2hours	2hours	14hours
2400*6600	3 hours	10 hours	3 hours	3 hours	19 hours
2600*6600	3 hours	12 hours	3 hours	3 hours	21 hours

1. Drying raw materialsoff to improve the oil yield and quality. Sort the articles which are unable to be refined such as stone,brick,wood and so on

2. Feeding:Feed some nonflammable wet raw material in case of fire if the furnace is still hot;Steel wires mixed in the raw material like shredded tires, leftovers from reprocessed paper factories, shall not be over fed, otherwise ,it may cause the machine running stop;The sufficient feeding is necessary, intermittent feeding is adopted that is feeding continually with the materials fed before partly melting;Keep the raw material fed enough and space inside reactor used without waste

3. Heating:Heating the reactor in high temperature in the early stage so that the moisture in the material can be evaporated as soon as possible;

4. Oil producing:Once exhaust gas nozzle burnt,it shows the oil begin to come out;Check the water in the condenser. Cooling effect directly decides oil yield;Adjust concentration of exhaust gas and air that goes through gas nozzle while oil is outputing. If more air and less exhaust gas, the concentration of gas mixture will be small. If more exhaust gas and less air, the concentration of gas mixture will be big

5. The gas mixturecan not be buring fully and will be wasted and produce pollution to air.If the runing machine is near to residential area,the environmental requirement will be much higher, so need to collect oil gas mixture smoking from feeding door and delivery them to furnace to be buring;Thermometer , temperature rise first and fall later,peak temperature should be controlled in 230 degrees celsius or so. Waste gas will be increased and oil yield will be reduced if too high.but time will be wasted if too low. So temperature should be proper.

6. Draft fan:keep chimney open when heating with fuel in case of pollution;Make screw tight at any time to avoid pollution caused by gas leak.Check the oil level lest oil overflow

1. Drying raw materialsoff to improve the oil yield and quality. Sort the articles which are unable to be refined such as stone,brick,wood and so on

2. Feeding:Feed some nonflammable wet raw material in case of fire if the furnace is still hot;Steel wires mixed in the raw material like shredded tires, leftovers from reprocessed paper factories, shall not be over fed, otherwise ,it may cause the machine running stop;The sufficient feeding is necessary, intermittent feeding is adopted that is feeding continually with the materials fed before partly melting;Keep the raw material fed enough and space inside reactor used without waste

3. Heating:Heating the reactor in high temperature in the early stage so that the moisture in the material can be evaporated as soon as possible;

4. Oil producing:Once exhaust gas nozzle burnt,it shows the oil begin to come out;Check the water in the condenser. Cooling effect directly decides oil yield;Adjust concentration of exhaust gas and air that goes through gas nozzle while oil is outputing. If more air and less exhaust gas, the concentration of gas mixture will be small. If more exhaust gas and less air, the concentration of gas mixture will be big

5. The gas mixturecan not be buring fully and will be wasted and produce pollution to air.If the runing machine is near to residential area,the environmental requirement will be much higher, so need to collect oil gas mixture smoking from feeding door and delivery them to furnace to be buring;Thermometer , temperature rise first and fall later,peak temperature should be controlled in 230 degrees celsius or so. Waste gas will be increased and oil yield will be reduced if too high.but time will be wasted if too low. So temperature should be proper.

6. Draft fan:keep chimney open when heating with fuel in case of pollution;Make screw tight at any time to avoid pollution caused by gas leak.Check the oil level lest oil overflow