Home  >  Printing Machinery  >  Pre-Press Equipment

Your personal imagesetter besides your desk - details see: https://www.machineto.com/my-image-setter-film-maker-10072779

1.How is LaserBlack used?

Images on monitor, printed on translucent paper or transparent film by laser printer, then go through our LaserBlack Enhancer can get dark enough density as traditional photo film for exposing plate directly to make all kinds of printing plate.

2.How is the result of it?

No matter what you print, we can make it 300 to 400% darker.

The density can be high up to 3.0 to 4.0 (Depends on your printer).

3.Does it effect the blank areas?

LaserBlackR is a clear solution, leaving no visible residue effecting the density in transparent areas.

4.Will it fix the toner image forever?

Yes, it will not only solve the toner evenly and stick on the surface forever but also will fill the gaps between the toner, it is really incredible. (See feedback from users. On our website)

5.Will it work on inkjet prints?

No, LaserBlack is designed for laserjet printers only.

6.How about consumption of LaserBlack solution?

A4 2000 sheets per liter, A3 1000 sheets per liter.

7.How about finest character and dot?

Character: 4 pt Dot: 150 lpi

It depends on your printer, no matter what you print, we just make it 300 to 400% darker density for you.

New generation printers such as 1200 x 1200 dpi can get finer print so as to get better enhanced results absolutely.

8.Is it really non-toxic and no harm to human?

Yes, we use hi-tech non-toxic solution, not harmful to human.

9.Can I use inside?

Yes, you can use it inside, only suggest to open the door for venting.

10.Any shipping problem?

No, as we do not use strong solvent, there is no problem of shipment.

11.What is a proper material for printer?

As long as it is a translucent paper or transparent film can be printed with your laser printer is good enough for our enhancer. However, if your need is critical,

will suggest you to use our paper or film to get best enhanced results.

12.After procession, is it really use water to clean off?

After operation just wash off your hands with tap water.

13.Can I use any brand of laser printer?

Yes, but will suggest to use HP or Canon for best enhancing results.

14.Is the density anything to do with drying method?

Yes, each set of LB enhancer attached with a Quick-Black Gun, suggest to use this Q-B gun to get quick and best results.

15.Can I use recycle toner cartrige?

Of course you can use recycle toner cartrige, sometimes, the enhanced result is better than the original one.

16.What kind of printing plate making can be used?

All kinds of plate making need a positive or negative film to expose the image can use LaserBlack R System. Now the density can reach 3.0, so it is no problem even to expose the longest exposure needed as for 7mm photopolymer plate directly for corrugated board printing.

17.Shall I adjust the enhancer frequently?

No, once the enhancer has been set up, you will not need to adjust it any more.

Unless you want to adjust it for applying more or less solution.

18.How about warranty from you?

One year warranty and after service for long.

19.Any tip to reach more black density?

We have made several experiments in our laboratory, in order to get darkest density for some users making critical plates, please refer to the following chart:

Density

It shows that if you lay down the paper 2-4 minutes after enhancing, then dry it with Q-B gun. The density can increase from 1.05 to 3.24 3.49, which means 309% to 332% black density increased. To put the enhanced paper aside for 2-4 minutes then drying it, you can get best enhanced results.

20.In addition to this, any other way to increase density?

To release the pressure between 2 rollers in oreder to carry more solution applying to paper surface, lay it down for 2-4 minutes then dry up will increase density definitely.