hydraulic round square steel pipe tube and bar induction heat bending machine

Carbon steel (seam & seamless) ,stainless steel ,

Power:Hydraulic

Other can be produced as customer’requirement

Φ168 – Φ530 Φ325 – Φ720 Φ426 – Φ820

Φ630 – Φ914 Φ720 – Φ1020 Φ1020 – Φ1620

Power Supply

700KW 750KW 800KW 1000KW

Alloy pipe

762×30mm

28.5-4.5-1.7m

219-762*30mm round carbon steel pipe

300X300mm,400X400mm square pipe.

R=3-30m, The max length is 12 m.

(EXW)

195,000 USD

Within the travelling expenses of the 3 staff 4800 USD, and the cost of PLC 10000 USD. We’d like to assist to handle the export and to deliver the goods to Tianjin Xingang, The buyer pay us for all the charges.

The Main Technical Parameters of The Pipe Bending Machine

1,Master cylinder:inside diameter:φ250mm diameter of the rod:φ210mm

effective strock:12m the max thrust of the 2 cylinders 210T.

The other smaller cylinders:φ125mm2 pieces.

2,Hydraulic pump station

............

3,The guiding part of the main machine is controled by four wheels, the clamp holding different size run

By the hydraulic motor, it open and closed drived by the oil cylinder, the oil cylinder drive the the rocking arm to adjust the bending radius.

4,Medium—frequency power supply:600 KW, 500-1000HZ.

The total power of the machinery part: 25KW,380V or 220V,50HZ or 60 HZ

5,Assembly parts

a,clamp wheels(four for the round pipe and four for the square pipe),fixture made of 45# cast steel

b,master fuselage,weldment,the main pushing board are welded board

c,screw,chain,standard parts and bearing are national standards

d,the guider is dovetail groove slide plate mode

e, The effective length of the bending radius adjust device is 30m (the part in the groun and the turning arm)

6,PLC(Siemens)

Angle setting show,distance and speed setting show,temperature show,with memory storage function,the bending angle sensed from the encoder,the terminal showed by the touch screen,During bending, computer records bending status at all times,Put the angle degree via the touch screen.With the infrared thermometer. The data and image of whole process can be stored and printed..

The works and the scope of supply of the supplier

1. Design and manufactureΦ762 pipe bending machine

2. Guide to install the equipment as the equipment arrives at the factory of buyer

3. Debugging and test run the equipment

4. Main machine part, hydraulic pump station.

5. fixture (clamps device):

A for square pipe :300X300mm and 400X400mm , 1 piece for each.

B for round pipe:φ219mm,φ304mm,φ406mm,φ457mm,φ508,φ610mm,φ762mm,

1 piece for each size.

6. Spindle for the turning arm : 2 pieces.

7. PLC device(Siemens):1 set.

8. The heeting device:

M-frequency ark: 1 set 600KW

The capacitor 1 set

The electric reactor 1 set

Water cooling cable 3mX2 pieces

Quenching transformer 3000KVA 1 set.

Induction heating coils:

A for square pipe :300X300mm and 400X400mm , 2 pieces for each.

B for round pipe:φ219mm,φ304mm,φ406mm,φ457mm,φ508,φ610mm,φ762mm,

1 piece for each size.

9. The equipment foundation drawing, hydraulic principle drawing, electrical diagram, machical drawing, manual operating instruction and the software back up for PLC, 1 coppy for each.

10. Send 2 engineer and 1 English speaker to the buyers factory to install and commiission the machine, It would take 20 days, based on the buyer get everything ready for the installation and commission before the technicians and after the machine get to the the buyers factor.The buyer supply the board and lodging during the term. If it takes more days for the buyer’s factor, the buyer would pay 25 USD for per person per day for the beyond.

11. The parts and the tools go with the machine, ( the list following)

The purchaser should prepare

1. the power source and the wire to the equipment electrical ark

2. cement foundation, steel ground, ground screw

3. the water cooling section of the M-frequency(50 m3 pool,50 m3 cooling tower, rate of flow:25

liter\hour, water pump with a head trip 30m, power: 7.5 KW Auxiliary water pipe valves,1set

4. the other type fixtures, reforming equipment, hydraulic oil

5. provide the hoisting and the necessary installation tools of the equipment and the raw material of test running

After-sales service

We are responsible for the repair in one year after the machine out of our factory, (except the human factors); the buyer supply the room and board to the engineer(s) during the term.

Payment terms

30% advance payment by T/T before the production,

65% by T/T before goods delivery.

5% by T/T after installation and commissioning.

piece/set