Home  >  Chemical Process Machinery  >  Chemical Machinery & Equipment  >  Other Drying Equipment

Plough knife mixer are widely used in chemistry, agriculture, fertilizer, medicine, dyeing, pigment, rubber, plastic, food etc. - details see: https://www.machineto.com/horizontal-plough-mixer-10293884

Plough knife mixer,Single shaft mixer, Horizonta powder mixer, Horizontal plough mixer:

1. Specification only for your reference

Type(m3)	Power(kw)	Rotate Speed(R/min)	(kg)(m3)/Batch	Dimension(mm)	Weight
LHY-0.3	3	41	<240	2300×680×1060	750
LHY-0.5	5.5	41	<400	2900×780×1240	1000
LHY-1	11	33	<800	3200×1000×1400	1800
LHY-2	15	33	<1600	3860×1200×1650	2200
LHY-3	18.5	33	<2400	4320×1300×1900	3200
LHY-4	22	28	<3200	4600×1400×2000	4000
LHY-5	37	28	<4000	4850×1500×2020	4650
LHY-6	37	22	<4800	5400×1560×2200	6280
LHY-8	45	22	<6400	5100×1720×2420	8500
LHY-10	55	19	<8000	5610×1750×2360	9300
LHY-15	90	17	<12000	5820×2000×2900	11000
LHY-20	110	11	<16000	6060×2630×3160	13500

2. Scope of Application:
In the U-shaped container, there are inner and outer ribbons. Special proportion of the two ribbons can be rectified with the kind of material, quantity and the proportion of body. This mixer has good effect on mixing viscosity or cohesion powder.

3. Working Principle:

a, The horizontal axes make the materials move up and down.
b, The outer ribbon gathering the material from sides to center and the inner ribbon pushing the material from center to sides.
c, Every screw makes the materials do axial and radial movement, the materials do relative cyclical movement so to gain the uniform mixings.

4. Characteristics:

a, high mixing speed

b, The rotation is under critical speed, which will reduce the effect of fragmentation to the material(e.g. crystal particle).
c, Lower height of the container is convenient for installation.
d, The inner and outer ribbons are set up at he same level, forming a mixing environment of low power, high efficiency.

5. Feeding inlet/access port:

Two types:

a, used in the complete mixing/ blending process: in order to connect the feeding device(e.g.screw conveyor), we design the connecting port.

b, used in the manual feeding: in order to operate and clean inside of the body, we design feeding inlet(s) or door(s).

6. Discharging:

There is a discharging valve at the bottom of the body/container. When mixing different types of materials, we use flat discharging valve.

The operation of the discharging valve should be convenient and there are three types: manual, air driven and electricity driven.

The manual discharging is operated on the valve and the open extent is controlled by hand freely.

The air driven discharging valve, assembled with cylinder, work under the air pressure.

The electricity driven discharging valve works under control of electricity control box.

7.Seal:

The mixing effect and the clean after-mixing environment depend on the sealing property. Our company provides various sealing devices according to difference of materials. The normal sealing structure is stuff seal and also called TEFLON seal. After using for a period, user(s) should fasten and enhance it. However, the dynamic seal has a long-time sealing effect and is especially fit for the powder, liquid.

8.Temperature control:

We can use a jacket when heating, cooling or heat-preservation is needed.

The jacket is filled by heat conduction medium. There are two kinds of heat conduction medium: water and oil. The water temperature should be limited in 90 and the oil temperature should be limited in 300. Heat the water or oil in the jacket by electricity