Home  >  Apparel & Textile Machinery  >  Textile Machinery  >  Other Textile Machines

1,Knitting Denim cylinder Making Machine, 2,no yarn mill and well-distributed waxing, 3,well-molded and easy to be unreeled - details see: https://www.machineto.com/high-speed-beam-warping-machine-10276515

WFGA137-B Knitting Denim cylinder Making Machine

WFGA137-B Knitting Denim Cylinder Making Machine is to unreel the beam dyeing warp collectively and twist it to cheese, with the character of large package, less connections or color shading, no yarn mill and well-distributed waxing. As well as being well-molded and easy to be unreeled, the machine is a new intelligent winder which combines the computer, AC variable frequency, servo control and other advanced technology.

General Specification:

Sectional Beam Size: 1800 mm (width) X 1000 mm (dia.)

Machine Speed: 5 ~ 130 MPM (adjustable)

End Break Detecting: Infer-Red Stop Motion Sensor

Cone Number: ≤ 480

Count of the yarn: 7S ~ 32S
Tension: 30 ~ 50 g/end

Cone size: Ø220 mm X 85 mm Or Ø150 mm X 155 mm

Main section of the machine:

1.Unwinding Head & Operation Station

2. Lease zone with stop motion detecting

3. Creel zone with re-winding system

4. Drive control system

Performance Feature

-Control the parking and speed system of the upper and lower shafts automatically by using the world famous programmable controller.

-Convenient and direct to monitor the running of equipments and analyze the error by using the world famous touch screen.

-Ensure to unwind in constant linear velocity by using the world famous servo control and motor.

-High qualified steel plates are placed as the left and right wallboards, well-constitutive and high rigidity, which makes the equipments operate more stably.

-Keep the warp beam from dropping off to hurt workers when the power and gas go off occasionally by using the special warp beam support mechanism.

-Package infrared ray cracked ends detection device with display, credible and sensitive.

-Equipped with waxing device.

-Make 400-600 cylinders once from Knitting Denim fabrics yarn.

Technical Parameters

Suitable yarn number	18—98tex
Warp beam available breadth	1600mm 1800mm
Disk sheet diameter of warp beam	800mm 1000mm
Speed of making cylinders	0~130m/min
Length of making cylinders	20S yarn 35000 meters
Number of head in making cylinders	400-600(user defined)
Operation monitor	5.5" touch screen
Input voltage	3×380V±10%
Installed capacity	3 servo motors, 3KM of each
Complete appliance weight	7000kg

Operation specification

(1) Close the power of the electric appliance box.

(2) Make sure that the emergency switch is on, press the initiation button. The power in on and the touch screen is light.

(3) There comes the main picture of cylinder making on the touch screen. Under the menu "techniques", set all the working parameters based on the requirements.

(4) When the warp beam is placed between the two brackets, run according to the established procedure:

When the warp beam rises, the warp beam clamps and brackets run down, open the compression roller front and back. Then pull up the pneumatic hand valve. After the yarn runs through the warp beam and the three-rolling mangle, press the compression roller.

(5) Press the initiation button to start the threading. If there happens an accident, press the "stop" button or the emergency button, then the machine will stop.

(6) Set up the tension parameter on the left operation panel according to the tension of yarn in need.

We are in charge of the installation

Daily maintenance

The following points are to be noted in the daily operation by the operators so as to maximize its life span:

-Rid up the chassis, all the drive parts and other flock powder or thrum. Clean the oil stain.

-Add oil or creesh in to the oil hole according to the provision.

-Check all the Connections and fastener in case of being adrift.

-Check the security and validity of the security and electric device.

Attention

-No working parameter can be changed in the motion of the machine.

-The machine should be shutdown if any error occurs in the operation. Based on the premise of reading the instruction book, check all the parts carefully. Any puzzling question should be told without delay and handled properly by the professional.

-Don't change arbitrarily the control procedure in the programmable procedure. Programmable procedure control is a general control unit. Users shouldn't insert programming unit nor change anything on it, otherwise severe accident may occur.

-The control parameter and program of the servo drive should not be changed. During the installation and debugging of the device, the parameters are settled. The random change may cause the wrong running or even damage the device.

-Replacing the parts of machine

1. The factory needs to be informed when replacing the programmable controller and servo drive.

2. Users can directly replace the servo motor with the same model. Otherwise, the factory should be informed.

3. Users can directly replace other low-voltage electrical components and standards of the same model.

MAIN EXPORTER(NOW):

WEB: http://singularity.en.alibaba.com/