Home  >  Chemical Process Machinery  >  Chemical Machinery & Equipment  >  Rotary Drying Equipment

sand dryer:, 1) High capacity dryer, 2) Smooth rotation sand dryer, 3) Low consumption dryer, 4) High output sand dryer - details see: https://www.machineto.com/high-effective-silica-sand-three-cylinder-dryer-10295021

High Effective Silica Sand three cylinder dryer

The brief introduction:

The dryer is a kind of mechanical equipment which uses heat energy to reduce the water content of materials.

If used in combination with our coal gasifier, our dryer can also be used for fine chemical drying.

Our industrial dryers are also regularly used in compound fertilizer production lines.

Working Principle:

Sand is sent into hopper by the conveyor and bucket conveyor, then the material pass through the feeding

tube into the feed end . The gradient of feeding tube must be greater than the natural angle of materials,

so that the material can enter into sand dryer. The desiccators' cylinder is an oblique rotating drum.

Heat-carrier enters into the dryer from the low-end that can form reflux with the material added from the upper end.

With the rotating of cylinder, materials are carried to the bottom end by gravity. In the moving process,

wet materials obtain the heat input of heat carrier indirectly to be dried. Then, the finished materials are sent out

by belt conveyor and screw conveyor, the wall plate of cylinder body can lifting the materials up and down,

increasing the contact area of material and air flow to improve the drying rate and promote the progression of

materials. The heat carrier is generally classified into the hot air flue, gas flue, etc. Dust cyclone need to capture

down the materials carried by gas. If the dust content of off gas needs to be reduced in further, Bag filter or wet

dust also should be used.

The application:

It is used for drying materials with a certain humidity or granularityin milling of ores, building materials,metallurgy and chemical industry. It has a strong adaptability of materials and it can dry various materials.

The operation is very simple and liable.

Main technical parameters:

Type (mm)	Gradient (%)	Rotation speed (r/min)	Inlet temperature (°C)	Power (Kw)	Volume (m3)	Capacity (t/h)	Weight (t)
Φ600×6000	3-5	3-8	≤700	3	1.69	0.5-1.5	2.9
Φ800×8000	3-5	3-8	≤700	4	4.01	0.8-2.0	3.5
Φ800×10000	3-5	3-8	≤700	4	5.02	0.8-2.5	4.5
Φ1000×10000	3-5	3-8	≤700	5.5	7.85	1.0-3.5	5.6
Φ1200×10000	3-5	3-8	≤700	7.5	11.30	1.8-5	14.5
Φ1200×12000	3-5	3-8	≤700	11	13.56	2-6	14.8
Φ1500×12000	3-5	2-6	≤800	15	21.19	3.5-9	17.8
Φ1800×12000	3-5	2-6	≤800	18	30.52	5-12	25
Φ2200×12000	3-5	1.5-6	≤800	18.5	45.59	6-15	33
Φ2200×18000	3-5	1.5-6	≤800	22	68.38	10-18	53.8
Φ2200×20000	3-5	1.5-6	≤800	30	75.98	12-20	56
Φ2400×20000	3-5	1.5-5	≤800	37	90.43	18-30	60
Φ3000×20000	3-5	1.5-5	≤800	55	141.3	25-35	78
Φ3000×25000	3-5	1.5-5	≤800	75	176.6	32-40	104.9

The silica sand be dryed: