Home  >  Construction Machinery  >  Building Material Machinery  >  Pipe Making Machinery

HG219 is used to produce round pipe 3" - 8" and square tube 70x70mm - 170x170mm. - details see: https://www.machineto.com/hg219-tube-mill-10081491

I. Summary

The mill is intended for manufacturing of round pipe of Φ89mm-Φ219mm with thickness of 2.0mm–8.0mm from cold-rolled and hot-rolled coil strip by means of unclosed tubular blank with its subsequent welding into tube, edge heating by means of solid state high-frequency welder, longitudinal seam welding in rolls of tube welding machine, cooling, further sizing or shaping and on-stream cutting of endless tube in measured lengths.

Finished product will be of round pipe, square and rectangle pipe.

II. The technical flow of the production line

{SteelTape}→→ Double-head un-coiler→→Five-roll Flattener →→Strip-head Cutter and welder→→Horizontal spiral accumulater →→Forming section(Flattening unit +Main driving unit +Forming unit +Guide unit +High frequency induction welding unit +squeeze roller)+ De-burr frame →→seam annealer→→

Cooling unit →→ Sizing unit and straightener →→Flying saw under computer-control →→ Run-out table

III. Basic conditions:

a)Steel Pipe Specification

1. Round Pipe diameter: Φ89mm-Φ219mm

Pipe Thickness: 2.0– 8.0mm

2. Square and rectangle pipe: 70x70-170X170mm

Pipe Thickness: 2.0 – 7.0mm

3. Pipe Length: 6.0m – 12.0m

4. Length Tolerance: 0-6mm

b) SteelTape Specification

1. Material: Carbon steel (δb≤500Mpa, δs≤235Mpa)

2. Steel Tape: Inner diameter: Φ600-800mm

Outer diameter: Φmax=1800mm

Strip steel width: 280mm-680mm

Strip steel thickness: 2.0mm-8.0mm

The maximum weight: 10.0 tons

c) Electric installed capacity: appro. 1200KW

d) Size of the whole line: appro. 120X14m

e) Line Speed: 10-50m/min

Forming & sizing section

5.1 Forming mill gearbox, universal joint

5.1.1 Mill entry flattener by up-horizontal roll and below-horizontal roll, one positive five-roll flattener, one pair of feeding vertical roll.

5.1.2 Forming mill consists of:

- Driven stand: 7 sets (Horizontal)

- Driven stand shaft: Φ 140mm

- Material of shaft: 42CrMo

- Side roll stand: 8 sets(Vertical)

- Side roll stand shaft: Φ90mm

- Material of shaft: 40Cr

- Gear box & universal joint: 7 sets

- Material of gear box: cast steel

- Material of gear: 20CrMnTi

- Main motor: 132kW Model: Z4-250-31 2 sets

- Main redactor: 2 sets

- Horizontal roller frame with worm gear & shaft. adjust up and down at same time and level.

5.2 Sizing mill gear box, universal joint

5.2.1 Sizing mill consist of:

- Driven stand: 6 sets (Horizontal)

- Driven stand shaft: Φ 140mm

- Material of shaft: 42CrMo

- Side roll stand: 6 sets (Vertical)

- Side roll stand shaft: Φ 90mm

- Material of shaft: 40Cr

- Gear box & universal joint: 6 sets

- Material of gear box: cast steel

- Material of gear: 20CrMnTi

- Main motor: 200kW Model: Z4-280-21 1 set

- Main redactor: 1 set

- 2 sets single head Turkshead, with 4 rollers*2sets

- One speed testing roller with air cylinder for CNC flying saw

- Horizontal roller frame with worm gear & shaft. adjust up and down at same time and level.