Finned Tube Used for Heat-Exchanger

Finned Tube Used for Heat-Exchanger, Base Tube Type: Seamless, Fin tube Type: High Frequency Welding, High Quality Low Price. - details see: https://www.machineto.com/finned-tube-used-for-heat-exchanger-10247076

Place of Origin:Shandong China (Mainland)	Brand Name:JIANNING	Model Number:HFW	Type:Fin Tube
Application:Heater Parts	Certification:ISO9001	Soldering Rate:>98%	Fin Material:Q195, SPCC, SPHE, 08F,304, 316L
Tube Standard:SA210 SA179 EN10216-2 GB3087	BaseTube Material:P195 P235 P265 SA210C 10# 20# 16Mo3 11CrMo9

High technology with competitive price and excellence service

Technical Parameters
Type of tubes:	Seamless
Base Tube Material:	Stainless or Carbon Steel
Base pipe O.D:	25-165mm
Fin Pitch:	4-30mm
Fin Height:	5-30mm
Fin thickness:	0.6-3.0mm
Soldering Rate:	>98%
Design Temperature:	Below 450°C
Application Pressure:	Max 5.88MPa
Bare Tube Standard:	SA210 SA179 EN10216-2 GB3087

1. Bare Tube Dimensions, Tolerance

1.1O.D Tolerance: ±0.8%*Out-Diameter

1.2W.T Tolerance: ± 5%*Wall-Thickness

1.3Straightness : Tubes be straight with a max deviation of 0.1 in. (2.5mm) in any 10ft. (3m) section.

2.Tolerance, Requirment of Fin

2.1Fin Spacing: The number of fins per unit length of tube shall be as specified, ±2 percent, measured over at least 12 inches of welded fins.

2.2Inclination: The fin is welded 90 degrees to the tube surface. Inclination of the fin will not exceed 5 degrees from the vertical for fin heights.

3.Finished Finned Tube Tolerance

3.1Stainless Tolerance: Finished finned tubes will be straight with a maximum deviation of 0.2 in. (5mm) in any 10 ft. (3.0 m) section

3.2Length Tolerance

Length ≤ 500mm , +2mm

500mm <Length ≤ 2000mm, +3mm

2000mm <Length≤ 5000mm, +5mm

5000mm < Length≤ 7000mm, +10mm

4. Fin-to-Tube Weld Requirements

4.1Weld Width: The average width of the weld bond between the fin and the tube shall be a
minimum of 90 percent.

4.2Weld Bond: During production, the weld bond on every fifth tube will be tested by removing one wrap of fin from the trailing end of the tube. The fractured surface of the fin-to-tube weld shall be visually inspected, and the arithmetic average width of the weld bond as evidenced by the white metal exposed shall be no less than 90 percent of the measured fin thickness. If the arithmetic average width of weld bond is less than 90 percent, the weld bond of the previously finned tube will be checked, (back to the previously inspected 5th
tube, if necessary), until weld bond that averages 90 percent is found. In the event of disagreement on the visual inspection, a tensile test of the fin-to-tube weld on a representative sample yielding the minimum average values, based on the measured fin thickness, shall be considered evidence of an acceptable weld.

Fin tube heat transfer area is 8 times than the light tube, high efficiency heat exchanger, more advanced than the other heat exchanger products.

Applicaton:Boiler Economizer, Heat Exchanger, Power Plant Waste Heat Boiler, Petrochemical Engineering.

Different kinds of finned tubes can be developed and designed according to your requirements in good quality

Workshop

Strict Base Tube Test, the Guarantee of high quality!

Third-Party Test by SGS

HF Welding Fin Tube Material
Bare Tube&Pipe Material	Fin Material
10# 20# 15CrMo Cr5Mo Cr9Mo1Cr18Ni9Ti SA106B SA106C SA192 SA179 SA178 SA214 SA210-A1,SA210-C TP304/304L/304H TP409/410 TP316/316L TP321/321L TP347H T11 T22 T91 etc	Q235-BF 08F 08AL 1Cr18Ni9Ti 0Cr13 1Cr13 CS A1008-13 SPHC SPCC TP304/304L TP316/316L TP321/321L

Other Third-Party Report We Can Provide

Application: Air-Cooler, Heat-Exchanger, Economizer, stream reforming furnace convection section etc.

High frequency welded helical finned tube is highly efficient heat transfer component,

HFW G L LL Kl Fin Tubes
Application	It is widely used for Heat exchanger ,Air-conditioner ,Refrigerator,Economizer and other parts of Heat Industry.
Material of base pipe	Carbon steel,Alloy steel, Aluminium or Stainless
Material of fins	Carbon steel,Alloy steel,Aluminium or Stainless
Type of base pipe	Seamlesss,Welded
Type of fins	G ,L Extruded.LL,KL,HFW
OD of Base pipes	15mm-219mm
Length of blank area	According to Customer's request.
Length of finned tubes	≤13m

Shandong Jianning is a leading manufacturers of quality finned tubes and finned pipe used throughout industry for heat transfer applications from China. Our products include High-Frequency Welded Finned Tube, Extruded Finned Tube, L

LL KL Type Finned Tube, Rolling Finned Tube, H Type Tube, G Type Embedded Finned Tube. We also supply Tube Heat Exchangers, Oil Coolers, Plate Heat Exchangers(PHE), Inter-Coolers, After Coolers, Steam Heaters, Air Pre-Heaters, Finned Tube Coolers, Fin Tube Heaters, Cooling Towers, Oil Chillers, Chilling Plants, Condensers and other HeatTransfer products.

Our well established team with in-depth technical understanding, assists the clients in customizing the products and meeting their exact requirements.

Packaging Detail:Packing In Boundles or Wooden Box.

Delivery Detail:within 40 days