automatic hydraulic sesame oil press machine 6YY-190
Condition:New | Usage:Sesame Oil | Type:Hydraulic press oil | Automatic Grade:Automatic |
Production Capacity:high | Place of Origin:Henan China (Mainland) | Brand Name:Ruihui | Model Number:6YY-190 |
Voltage:3 phase 380v 50hz | Power(W):1.5kw | Dimension(L*W*H):980*880*1550mm | Weight:950kg |
Certification:CCC,iso9002,CE | After-sales Service Provided:Engineers available to service machinery overseas | KN pressure:1900KN | Max work pressure:55Mpa |
Heating Ring power:3kw | Heatinf ring control temperature:70-100 degree | Sesame feeding/time:10-15kg | Motor power:Y901-4 1.5kw |
NO.1 Application scope
Automatic hydraulic oil press is the most advanced equipment and it is a best choice instead of hand-operated workers currently. It is the easiest machine for people to operate and replace wearing parts least with the
highest oil yielding rate among all the range of machines. Besides, it is particularly suitable for people from large cities
to spend less money to buy real goods because of less amount of squeezing per time(2-8 kg / time), and it needs
shorter time(8-l2 minutes / time) for processing.
In addition, it can ensure fast processing on giving materials in rural towns,which is known as assured oil.
The main processing oil crops are: olives, cashew, sesame, walnut, camellia, pine nuts (Peeling most effective), almond
and other high oil crops.
NO.2 Structure
1.Main body
It consists of bottom-board, column, pressing chamber assembly, drip tray, nuts, etc. The main body is one of main
parts of the machine, in which the crops in chamber are pushed upward by the force from cylinder,
through the drip tray, oil flows down from lines to the drum.
2.Hydraulic transmission
This is the main power source of the machine, which consists of the transmission shaft, worm wheel, worm,
gear pumps, high-pressure pump, relief valve, manual valve, cylinder assembly, pipe joints and other parts.
This machine adopts the most advanced hydraulic pump stations in the world, comparing with the national second-class piston pump. The advantage is low speed, higher pressure and could withstand high temperature. Besides, it
can keep working above 65 degrees without the cooling device.
3.Electrical control
It is the advanced core of the machine, which consists of motor, voltmeter, temperature reconciliation sheet, pressure
gauge, control fuse, and other units.
NO.3Performance & characteristics
1.It is easy for people to learn, understand, and operate because of its small size. Besides, it is no special requirements
for people to operate.
2.It costs less various expenses with lower electricity consumption in use.
3.The machine is a hydraulic machine with high pressure, high oil yielding rate and pure oil quality.
4.The machine adopts automatic control system,automatic preheating temperature control and automatic pressure
control of hydraulic system.
NO.4 Main data
1.Max pressure reaches 55Mpa
2.Capacity
Oil crop | Minutes/time | Weight/time(kg) | Handling capacity(24 hrs) | Yielding rate (%) |
sesame | 5-8 | 6-9 | 860-1600 | 42-52 |
walnut | 8-12 | 6-9 | 620-1400 | 50-60 |
Pine nut | 8-12 | 6-8 | 740-1600 | 45-60 |
Note: The data listed above in the table is only the reference for operators with different skills. Besides, the oil crops
should be dry, full and clean.
NO.5 Operating instructions
Precautions before starting:
Clean up the tank, and add enough hydraulic oil.
Check bolts to make sure it is loose or not.
Check the wiring connecting to make sure it is correct.
1.Preheating should be made before oil squeezing. The preheating temperature is 50--70 degrees in summer and
autumn, and 70--90 degrees in winter and spring. Preheating system is controlled automatically.
Therefore it is unnecessary to turn off the thermostatic switch.
2.The wrench handle of the top ejector plate should be opened completely: The angle between the top ejector plate
and work position is 180 degrees, and the mat should be put in the bottom of chamber. Besides, the piston should be
put in place for preparation.
3.The machine without oil plants should be run for 1-2 times before extruding. If hydraulic oil becomes dense in winter or spring, the machine should be run for 5-10 minutes to make hydraulic oil diluted, which is convenient for people to operate.
4.Fried plants should be put into the chamber after the smoke has been discharged.
5. The mat should be put on the top of oil crops in the chamber, and the stainless disk above plants for separating the
plants should be pushed into the chamber. If oil crops are not enough, the oil crops can be raised to keep the upper
plane of plants lower than the fault plane of the chamber when the machine is started. Otherwise, the top ejector plate
cannot be closed. The machine should be started for squeezing if all the operations are done.
6.There must be skilled person to operate, and you can not leave the main engine when pressure is rising. When it
reaches 50Mpa, motor stops working, or you should turn off the power immediately. Check if pressure gage and AC
contactor is damaged or defective, if damaged, you should replace them immediately, Check each part correct and
then start to use.
7. When the pressure rises to 55 Mpa, the electrical control system automatically stops. When the pressure drops to
45 MPa, the electrical control system will automatically open. The pressure gauge rises again. If there is no oil leakage
out of the oil seam, which shows the oil has been drained completely.
8. Starting:hold the handle to push down the manual valve, allowing chamber to drop lower 10 mm from the upper
cover.Hold the manual valve handle to open the roof cover.
9.Stopping: when oil cakes rise up. the upper surface of piston is higher approximately 5mm than the chamber. Then
you should shut down the machine, remove the felt mat, separate the disc, and take out the oil.
10.Push down the handle, and make the piston fall down to prepare for the second time squeezing.
NO.6Security technology & maintenance
1.The machine adopts 380-volt power supply. Heating and control system adopts 220-volt power supply, the motor can be changed to 220-volt according to requirements of customers.
2.Protective Grounding of Power must be adopted to ensure the safety of electrical system.
3.The pressure of hydraulic system is 55 MPa, which belongs to extra high-pressure level. It is prohibited to use in the condition of overpressure. Besides, it is also prohibited to adjust and
disassemble the machine.
4. It is not allowed to operate the machine when the pressure gauge is damaged. Besides, it is not permitted to open
the machine until the pressure gauge is replaced.
5.The machine is not allowed to repair in the period of high pressure and pressure retaining.
6.Operate strictly in accordance with operating procedures during operating processes
7.After frying plants, smoke must be eliminated completely if oil crops have been fried. Otherwise hot-gas will
break out, which maybe injury people.
8.After Oil plant drains completely, the cake should be get out of chamber immediately, or else the outbreak of gas
will appear.
9.If the oil seam is blocked, it should be sorted by thin blade or needle in time.
10.If the new machine is used for one month, hydraulic oil should be filtered thoroughly. Besides, Hydraulic Oil once
a year should be replaced and the oil tank should be made clean. If it's disused for a lng time,please turn off the power.
11.The name plate on the top of machine is an important symbol in our company. If remove it at random, we will not
supply warranty.
Packaging Detail:woodencase package or sustomed. |
Delivery Detail:within 7 days after receipted 30% deposit |