Air cooling single cylinder four stroke diesel engine
diesel engine, 1.Strong Power, Fast Actuate, 2.Light Weight, High Quality, 3.Low Fuel, Low Vibration, 4.CE - details see: https://www.machineto.com/air-cooling-single-cylinder-four-stroke-diesel-engine-10232902
Condition:New | Usage:Other | Fuel:Gasoline | Stroke:4 Stroke |
Cylinder:Single Cylinder | Cold Style:Air-cooled | Start:Kick Start | Place of Origin:Henan China (Mainland) |
Brand Name:ANTAI | Model Number:GX390 | Dimension(L*W*H):545*455*470 | Weight:36kg |
Certification:CE | Warranty:three month | After-sales Service Provided:Overseas service center available | key words:diesel engine |
Model:GX390 | Cubic cc:390cc | Cooling system:Air | Rpm:3000/3600 |
maximum power:9.6kw | rated frequency:60hz | Transmission:Threaded shaft/taper shaft, spline shaft | system:Remote control system |
starter:Electric starter |
Air cooling single cylinder four stroke diesel engine
1, starting
The height of the coolant level in the radiator pipe connector fastening surface height of the oil in the oil pan, the amount of fuel in the fuel tank and fuel system piping and joints in good condition, the battery electrolyte fastening joint fluid levels, batteries, generators, starters and other electrical equipment.
2, steps of starting
The shift lever of the transmission is placed in neutral position, depress the clutch pedal, to relieve the load on the engine when starting. Cold, hot car, starting not to step on the gas pedal, the fuel injection quantity is automatically controlled by the ECU starter. The key turning the ignition switch so that it is placed at the starting position, start the engine, but each start time can not be more than five seconds, twice starting time interval shall not be less than 15 seconds.
3.shut down
Engine at high load operation, you need to stop working, you should reduce the speed and reduce the load, run for 2-3 minutes and then turn off the ignition switch to stop working in the idle state. Its purpose is to make the engine cooled uniformly, and to avoid some parts of the deformation caused due to the rapid cooling.
2, steps of starting
The shift lever of the transmission is placed in neutral position, depress the clutch pedal, to relieve the load on the engine when starting. Cold, hot car, starting not to step on the gas pedal, the fuel injection quantity is automatically controlled by the ECU starter. The key turning the ignition switch so that it is placed at the starting position, start the engine, but each start time can not be more than five seconds, twice starting time interval shall not be less than 15 seconds.
3.shut down
Engine at high load operation, you need to stop working, you should reduce the speed and reduce the load, run for 2-3 minutes and then turn off the ignition switch to stop working in the idle state. Its purpose is to make the engine cooled uniformly, and to avoid some parts of the deformation caused due to the rapid cooling.
diesel engine:
Model | GX390 |
Cooling method | Air-cooled |
Type | Single cylinder, four stroke, air-cooled, overhead type gasoline engine |
Bore× Stroke(mm) | 88*64 |
Lube.brand | SAE15W/40 |
Compression ratio | 8.2:1 |
Engine Speed | 3000/3600 |
Rated power(kw/rpm) | 7.2/3600 |
Max.outpur | 13HP |
Fuel type | 90# Unleaded Gasoline |
Fuel tank capacity(L) | 6.5 L |
Fuel consumption Rate(L/hr) | 2.15 |
oil capacity(L) | 1.1 |
Oil consumption ratio | ≤6.8 ( g/kw.hr ) |
Alimentation | Natural |
Starting method | Recoil manual start or electric start |
Packing size (L× W× H) (mm) | 545×455×470 |
Net/ gross weight(kg) | 34/36 |
diesel engine picture:
Packaging Detail:carton packing |
Delivery Detail:15-25 days afteryou payment |