Home  >  Industrial Supplies  >  Laser Equipment Parts

Rated power 90w and Maximum Power 100w, Maximum10, 000 Hours Life Span, Better Performance, Higher efficiency - details see: https://www.machineto.com/80w-co2-laser-tube-10230909

80W co2 laser Tube

Rated power 90w and Maximum Power 100w
Maximum10, 000 Hours Life Span
Better Performance
Higher efficiency

Highlights:
Output Power: W2 rated power 90w and Maximum Power 100w. The production process of the tube is standardized, so the output power and output model are guaranteed. Its cutting effect and cutting speed is the same as 90w laser tube of other brands. (The other laser tubes are handmade and its quality is different from one tube to another)
Long life span: We have catalyst plating in the inner wall of the laser tube. Designing lifespan is 10,000 hours and the warranty is 10 months. (No catalyst technique is used by other laser tubes manufacturers. Their lifespan is 3000 hours and the warranty is only 3 months)
Appearance: The tube is sealed by metal material. It is industrial product. (No metal material is used by other manufacturers. Their tubes are handmade and need extra water cooling for front and rare mirrors).
Tube frame: This is exclusive design for Reci laser tube. You can use it to install our laser tubes into the machine to spare the freight cost. This frame is shockproof and makes sure the tube will not move during the transport. (No frame is provided by other manufacturers.)
Length: The length is only 1.2m. It reduces the volume of the machine and minimizes freight cost. (The length of other 80w tubes is 1.64m. 300mm must be projecting in the machine. That costs more for machine panel, package and transport)
High photoelectric conversion rate: No compression type Water Chiller should be equipped. The output power will decrease for less than 1w when the cooling water’s temperature is 42°C. Its heat productivity is lower than 60w tubes of other brands. (Other brands: The output power decreases rapidly when the cooling water’s temperature is 42°C)
Very good engraving function: It can compare with 50w laser tubes of other manufacturer. The tube can engrave with 5mA working current when there is still no laser beam in the laser tube. (Other brands: No engraving function)
Warranty: 10 months, international warranty service, Reci charges the freight for exchanging the defect tube. (For others laser tube brands: warranty for 3 months, no international warranty service)
High performance cost ratio: When you buy Reci 80w tube, you can spare money for machine sheet metal, transport. Besides, you get 10 months warranty and the top level after sale service.

Specifications for industrial CO2 laser tubes

Length	47" (1200mm)
Power Output	Rated power 90w and Maximum power 100w
Outer Diameter	3.15" (80mm) ± 2mm
Ignition Voltage	19kv
Operating Current	Test current is 29mA. Maximum working current is 29mA. The running current must be kept below 27mA. The life span can reach 8,000 hours if the current is kept below 25mA.
Power Stability	≤ ± 2%

Terms & Condition of Purchase: After we receive PO from customer with stamp, we give PI for customer.
Lead Time: After receiving customer's deposit, within 1-4 days.
Wooden Box: There is total one wooden box.

Tube Size	3.15" x 47" L (80mm x 1200mm L)
Tube Weight	4.4lb (2kg)
Package	Fumigation free package
Packing Size	1450mm x 350mm x 350mm (57" x 14" x 14")
Gross Weight	39.6lb (18kg)

Packing List

No.	Name	Qty
1	Laser tube	1 set
2	Copy for W2 Operation Instruction	1 set
3	Copy for Quality Assurance	1 copy
4	Copy for W2 Installation Instruction	1 copy

Package:

Quality Assurance
1. The warranty period for the first buyer is 300 days.
• If fracture in the glass structure of laser tube occurs within 7 days after the first buyer gets the product, the company is responsible to exchange for free. The company shall not take the responsibility from the 8th day.
• Within 180 days of the date after manufactured, if the user follows the instructions and the power output happens to be lower than 85% of the rated output, our company shall exchange or repair the laser tube with a new one for free. The replaced laser tube enjoys the quality guarantee as the new one from the manufacturing date. The user should pay for one way freight for repair. The company is not responsible for any damage and change of laser structures.
• From the 180th to the 300th days after manufactured, if the user follows the instructions and the power output happens to be lower than 85% of the rated power output, the company shall provide either repair or replace the laser tube with our special tube (depending on specific case) for free. The user should pay for one way freight for the repair. The company is not responsible for any damage and change of laser structures. The warranty for tubes exchanged during this period is four months.
2. The quality assurance is invalidated to the special offered products or customized products.
3. The user must follow the instructions for W2; otherwise the quality guaranteed assurance is invalidated.
4. The matched power supply for each model must be equipped; otherwise the quality guaranteed assurance is invalidated.
5. The returned W-Series products must meet the following qualifications; otherwise the quality guaranteed assurance is invalidated.
1) The appearance, structure and certificate are in good condition.
2) The surface of output mirror is not polluted, cut or splitted.
3) The exterior surface of the negative electrode container shall NOT in light yellow, and the discharge area within the electrode container shall NOT more than 55%.
(The two phenomena are in direct proportion with the intensity of current flow and the usage of super-current. We mainly rely on this method to measure whether the laser is in over-high current state for long time. If this happens, we shall not provide guarantee for the laser. So the user must pay attention in case of losses.)
6. Standard for delivery: W2 rated power 90w and Maximum power 100w.
7. Quality assurance for W2 CO2 Laser is valid before January 1st 2013 and the next adjustment is allowed. Please refer to the next adjustment as final in case of conflict in contents. As for the products made before the next adjustment, please stick to the current quality assurance.

Operating Instruction:

1. Installation Requirement
Make sure to follow the operation instructions of model W2 as shown in the illustration. The dedicated power DY10 should be equipped. The positive pole is in high voltage (the ignition voltage is 19kv). It may cause the following consequence when it is failed to follow the instruction: Arcing; the inner tube will be punctured by electricity and may cause water leakage.

2. Operation conditions
-Water cooling: using purified water; 2 to 5 liter/minute; water temperature: 10°C-40°C.
-The operating environment: temperature 2-40°C, humidity 10-60%.
-The working current: test current is 29mA. Maximum working current is 29mA. The running current must be kept below 27mA. The life span can reach 10,000 hours if the current is kept below 25mA. The ammeter indicating current must be connected to the negative electrode of the laser tube.
-When it is working under over-high current for long term, the negative pole will appear light yellow, and the life span will be reduced rapidly.
-To protect dust from going into the insulation sheath, please wrap it with plastic film.

3. Working Performance
-Cutting function.
-Engraving function: Very good, when the working current is 4mA and the tube is in the state of preionization, the laser can be used for high-frequency impulse engraving.

4. Key Notes
Do not clean the exterior surface of the output widow mirror with tools such as tampon; otherwise the output power will be seriously affected. The followings are the designated methods to clean up pollution in the exterior surface of window mirror:
1) When the mirror is polluted, do not turn on the laser.
2) Blow the mirror surface sideway with air blower.
3) Spray the pure alcohol on the mirror surface with sprayer.
4) Turn on the laser after the alcohol gets fully volatilized.
5) If the methods above don't work effectively, it is necessary to ask for the professional to use tampon with alcohol to clean the mirror surface from middle to edge. The best solution is to prevent the window from being polluted.
Attention:
It is forbidden to clean the mirror with acetone.
The screw in the front and back ends of the laser tube is not allowed to be moved, otherwise the out power will be declined and even the tube may be scrapped.
Put the acryl 300mm far away from output mirror, when testing the laser spot.

5. Safety
The laser beam is invisible light. Please wear protective glasses when debugging the laser. The positive pole is in high voltage. Pay attention to the security marks.

6. Storage and Transportation Requirement
Pour out cooling fluid in the event of storage and transportation, and cover the output terminal with a dust-proof plastic bag. The storage environment is 2-40°C, and the requested humidity is 10-60%. Pack the laser as in the original way.
Important notes: it is requested to cement the sponge together with laser tube to prevent the tube vertically sliding during transportation. The sponge in the side of output mirror must be 70mm beyond it, and the sponge in the side of reflecting mirror must be 50mm wider.

7. Tubes operated in wrong way will not be guaranteed by Manufacturer.