Home  >  Metal Processing Machinery  >  Machine Tool Equipment  >  Welding Equipment  >  Butt Welders

630 plastic aluminum welder, 1.Apply to pe hdpe plastic pipe, 2.plastic aluminum welder, 3.CE, 4.Light weight and high efficienc - details see: https://www.machineto.com/630-plastic-aluminum-welder-10135062

Application:

PEpipes welding machine;

HDPEpipes welding machine;

PPpipes welding machine;

PBpipes welding machine;

PVDFpipes welding machine;

any other plastic pipes available for welding... ...

Further parameters:

Model	SHBD315	SHBD450	SHBD630
Welding diameters (mm)	160,180,200,225, 250,280,315	280,315,355, 400,450	400,450,500,630
Heating plate temperature	270°C	270°C	270°C
Heating plate surface temperature(170-250°C)	<±5°C	<±7°C	<±7°C
Pressure adjustment range	0-6.3MPa	0-6.3MPa	0-6.3MPa
Cross-sectional area of the cylinder	2000mm2	2237mm2	2306mm2
Working Voltage	220V,50Hz	380V,50Hz	380V,50Hz
Heating plate power	3.1KW	5.2KW	9.2KW
Milling cutter power	1.36KW	1.5KW	1.5KW
Hydraulic station power	0.75KW	1.5KW	1.5KW
Total Power	5.21KW	8.2KW	12.2KW

Our advantages:

• The main parts of the machine foraluminum, using standard ZL104, which make working moreenvironmentally friendly and efficiently... ...

• The mainelectrical componentsare imported overseas, which are more reliable and stable, extend the life of welding machine and performance more efficiently.
• Our machine will be spread a layer of oil, and then be wraped by plastic film, put into a wooden box at last. This type of packages is avoid getting rusty easily.

Operation instruction:

• The od card which matches the pipes must be used. Stuck the pipe tightly then fix them on the rack.
• Open the ends of pipes,put in the milling cutter, and fix the milling cutter on the rack. Start the milling cutter, mover forward the cylinder,close the fixture and cut the ends. when it forms into thecontinuous chips, lower the pressure to zero firstly, then open the fixture and close the milling cutter at last.
• Put down the milling cutter, close the ends, and check up the pipe of the two ends. Check up the temperature of the heating plate. For the first welding, the temperature of the heating plate should be heated over the pre-heated temperature . Every time for welding, the heating plate must be cleaned.
• Put the heating plate with the suitable temperature on the rack, close the fixture, make the end meets the end meets the heating plate fully and set the system pressure.
• When the end raises uniformly and the height of the crimps meet the requirements, the heating time should be lowered at the same time.
• When it get to the endothermic time, open the fixture quickly and remove the heating plate.
• Close the fixture quickly, adjust the pressure uniformly in the specified time and write down the cooling time.The pressure should be kept until the ends cool down completely.
• When it gets to the cooling time, adjust the pressure to zero, open the fixture, and remove the welded pipe.

Assistant tool:

• This istrailerhelping to move the butt fusion welding machine.
• You make one order for thistrailer, if you have a requirement.

• The trailer

  http://preview.alibaba.com/product/1117931002-219028685/Trailer_for_pe_hdpe_welding_maching.html

• This is lifting plateform helping to move the milling cutter.
• You make one order for thislifting plateform, if you have a requirement.
• The lifting plateform http://preview.alibaba.com/product/1118093979/jinan_bada_electric_hoist_selective_for_welder.html?memberid=&productid=1118093979

Operation instruction:

• The od card which matches the pipes must be used. Stuck the pipe tightly then fix them on the rack.
• Open the ends of pipes,put in the milling cutter, and fix the milling cutter on the rack. Start the milling cutter, mover forward the cylinder,close the fixture and cut the ends. when it forms into thecontinuous chips, lower the pressure to zero firstly, then open the fixture and close the milling cutter at last.
• Put down the milling cutter, close the ends, and check up the pipe of the two ends. Check up the temperature of the heating plate. For the first welding, the temperature of the heating plate should be heated over the pre-heated temperature . Every time for welding, the heating plate must be cleaned.
• Put the heating plate with the suitable temperature on the rack, close the fixture, make the end meets the end meets the heating plate fully and set the system pressure.
• When the end raises uniformly and the height of the crimps meet the requirements, the heating time should be lowered at the same time.
• When it get to the endothermic time, open the fixture quickly and remove the heating plate.
• Close the fixture quickly, adjust the pressure uniformly in the specified time and write down the cooling time.The pressure should be kept until the ends cool down completely.
• When it gets to the cooling time, adjust the pressure to zero, open the fixture, and remove the welded pipe.

ABOUT US:

• we are professional plastic pipe butt fusion welding manufacturer in china.
• we can offer the great quality welding machine but low price to service our customers.

ANTICIPATION AND YOUR COOPERATION

S.MIYA

TEL/FAX:86-0531-88773369

Skype account number: miya888269