Home  >  Metal Processing Machinery  >  Machine Tool Equipment  >  Bending Machines

1.hydraulic press, 2.OEM acceptable, 3.vertical four column, 4.PLC control, 5.finish modes include extruding and running - details see: https://www.machineto.com/4-column-hydraulic-press-10124040

Main body

The main body is organized by press crown, beam, working table, uprights, locknuts and adjusting nut. There are guide sleeve to be employed inside the beam. The precise can be adjusted through adjusting the locknuts and adjusting nuts that tightened on the press crown. There are T-type channels on the beam and working table, so that the tools can be equipped convenience

Main cylinder

Main cylinder is fixed on the press crown

Stroke limited equipment

The stroke limited equipment is installed on the left side of the machine, it can control the stroke distance, the beam stroke distance can be adjusted by adjusting the distance of the travel switch.

Hydraulic Station

It’s including oil container, axial plunger pump, motor, two-ways cartridge valve, oil cleaner, air cleaner.

Press gauge and overflow valve are equipped on the oil container so that the operator can observe the hydraulic pressure and adjust the oil pressure easily.

Cartridge valve equipped for hydraulic system, reliable, durable and less hydraulic shock.

The machine is equipped the hydraulic supporting safety loop to keep the security when the beam is out of control.

Water cooler is employed to cool the temperature of the hydraulic oil to keep the oil temperature doesn’t exceed 55°C. When the oil temperature is over 45°C, connect the water cooler system, the system will give a alarm when the oil temperature is over 50°C; When the oil temperature reach 55 °C, the control system will cut off the power to keep the oil temperature not over 55°C.

Electric control system

The electric cabinet is separate from the main structure, this machine is supplied with the moving operating panel so that the operator can operate machine at a big area range.

Power: AC380V,50 Hz

Operating system

1 Inch actionMainly used for adjust the machine and change tools,

2 Manual

3Semi-automatic: press the respectively buttons to finish one working circle

3.1Without knock out techniques,

Beam down in no-load mode →beam switch to work mode by proximity switch → beam down in work mode till desired force achieved→ start time relay when desired force achieved → beam all way up after time on time relay runs out

3.2 With knock out techniques

Beam down in no-load mode →beam switch to work mode by proximity switch →beam down in work mode till desired force achieved→ start time relay when desired force achieved → beam all way up after time on time relay runs out →knock out cylinder at upper limit start time relay→ knock out cylinder return after time on time relay runs out

3.3Drawing techniques

Beam down in no-load mode →beam switch to work mode by proximity switch → beam down in work mode till desired force achieved→ start time relay when desired force achieved → beam all way up after time on time relay runs out

4.Working environment

Temperature: 0°C - 40°C2. Humidity: relative humidity is under 90%.3. Voltage: 380V(-15%,+15%),3P,50Hz

Security protection

Beam upper limited is protected by the light curter

With “PAUSE” & “EMERGENCY STOP” button.

With Second supporting loop for the main cylinder

Security valve for hydraulic loop

Main components

Transformer: Simens

Middle relay: Simens

Time relay: Simens

Breaker: Simens

Thermal relay: Simens

Oil pump: 25YCY14-1B Chinese famous brand

Main motor: Simens

Valves: TAIFENG

Seals: PARKER

Buttons: Simens

PLC: Mistsubushi

YP32 series of four-column hydraulic press main specifications and technical parameters
Item		Model
		unit	YP32-200	YP32-315F	YP32-400A	YP32-500	YP32-630	YP32-800	YP32-1000
Nominal pressure (KN)		KN	2000	3150	4000	5000	6300	8000	10000
Knock-out pressure		KN	400	630	630	1000	1000	1250	2000
return stroke pressure		KN	360	600	830	930	850	720	1060
Max working force		Mpa	25	25	25	25	25	25	25
Ram stroke		mm	710	800	800	900	1000	1000	1000
Knock-out stroke		mm	250	300	300	300	300	350	450
Max.opening height		mm	1120	1250	1250	1500	1600	1600	1600
Ram speed	Free	mm/s	120	120	120	120	120	150	150
	Work		7-18	6-12	7-18	7-15	6-12	6-12	5-12
	Return		100	60	92	80	80	120	100
Knock out speed	Knock-out	mm/s	90	55	120	75	75	80	60
	Return		160	100	210	160	160	160	120
Work table size	right and left	mm	930	1260	1260	1980	1880	1880	2000
	Before and after		900	1200	1250	1600	1600	1600	1800
stand column distance	right and left	mm	1050	1400	1500	2200	2100	2100	2360
	Before and after		700	900	950	1300	1200	1200	1400
height of worktable to ground level		mm	550	650	710	500	500	/	/
Motor power(KW)		kw	15	22	30	44	44	60	74