M660A ac stepper motor, 6A stepper motor driver, ac and dc steper motor driver

votage range:24vAC-60vAC, current range:2.0A-6.0A, high performance digital stepper motor driver, ac motor driver - details see: https://www.machineto.com/m660a-ac-stepper-motor-6a-stepper-motor-driver-ac-and-dc-steper-motor-driver-10234862
Place of Origin:Jiangsu China (Mainland)Brand Name:JSSModel Number:M660AMotor Type:AC Motor
current range:2.0-6.0Avoltage range:24-60v AC  
M660A ac stepper motor, 6A stepper motor driver, ac and dc steper motor driver
contact supplier for M660A ac stepper motor, 6A stepper motor driver, ac and dc steper motor driver


M545D dc stepper motor driver features:

1. high performance

2. over current, over voltage, under voltage, over heating, autmatic semi-flow prection fuctions

3. anti-noise, low vibration

4.dimensions: 142mm×99mm×48mm
5. drive all the 2 phase, current under 6.0A stepper motor

6.Working environment: temperature: 15-40, humidity <90%

Current selection

REFPeakSW1SW2SW3
2.00A2.40Aononon
2.57A3.08Aoffonon
3.14A3.77Aonoffon
3.71A4.45Aoffoffon
4.28A5.14Aononoff
4.86A5.83Aoffonoff
5.43A6.52Aonoffoff
6.00A7.20Aoffoffoff

Microstep selection

Pulse/RevSW5SW6SW7SW8
400onononon
800onoffonon
1600ononoffon
3200onoffoffon
6400onononoff
12800onoffonoff
25600ononoffoff
51200onoffoffoff
1000offononon
2000offoffonon
5000offonoffon
10000offoffoffon
25000offononoff
50000offoffonoff

Driver functions descriptions

Driver functionOperating instructions
Output

current

setting

Users can set the driver output current by SW1-SW3 three switches.

The setting of the specific output current, please refer to the instructions of the driver panel figure.

Microstep settingUsers can set the driver Microstep by the SW5-SW8 four switches. The setting of the specific Microstep subdivision, please refer to the instructions of the driver panel figure.
Automatic half

current function

Users can set the driver half flow function by SW4. "OFF" indicates the quiescent current is set to half of the dynamic current, that is to say, 0.5 seconds after the cessation of the pulse, current reduce to about half automatically. "ON" indicates the quiescent current and the dynamic current are the same. User can set SW4 to "OFF", in order to reduce motor and driver heating and improve reliability.
Signal interfacesPUL+ and PUL- are the positive and negative side of control pulse signal; DIR+ and DIR- are the positive and negative side of direction signal; ENA+ and ENA- are the positive and negative side of enable signal.
Motor interfacesA+ and A- are connected to a phase winding of motor; B+ and B- are connected to another phase winding of motor. If you need to backward, one of the phase windings can be reversed.
Power interfacesIt uses AC power supply. Recommended operating voltage is 24VAC-60VAC, and power consumption should be greater than 350W.
Indicator lightsThere are two indicator lights. Power indicator is green. When the driver power on, the green light will always be lit. Fault indicator is red, when there is over-voltage or over-current fault, the red light will always be lit; after the driver fault is cleared, if re-power the red light will be off.
Installation

instructions

Driver dimensions:142×99×48mm, please refer to dimensions diagram. Please leave 10CM space for heat dissipation. During installation, it should be close to the metal cabinet for heat dissipation.

.

M660A ac stepper motor, 6A stepper motor driver, ac and dc steper motor driver
Packaging Detail:corton
Delivery Detail:20-25

Related Product for M660A ac stepper motor, 6A stepper motor driver, ac and dc steper motor driver